How to Move a Washer and Dryer Safely

Washers and dryers are among the heaviest things in an ordinary house, and they are almost always tucked into the most awkward spot: a basement, a narrow laundry closet, or a second-floor alcove that was clearly designed around the house rather than the appliances. They also have water, power, and sometimes gas connected to them, which means a careless move can leave you with a flooded floor or worse.

The good news is that moving a washer and dryer is mostly preparation. If you get the disconnect, draining, and securing right, the actual lifting is straightforward with the right equipment.

How Much Do a Washer and Dryer Weigh?

Weight depends on the model and type, but these are typical ranges:

Top-load washers usually weigh 100 to 150 pounds.

Front-load washers usually weigh 150 to 230 pounds, because they use concrete counterweights to keep the drum steady during spin cycles.

Dryers usually weigh 100 to 150 pounds. Gas and electric models are similar.

Stacked units and pedestals add weight and height, and a stacked pair is top-heavy. Always separate them before moving.

These are not weights you want to handle by hand, especially on stairs.

What You Need

An appliance dolly with straps. A regular hand truck will work on flat ground, but an appliance dolly with a ratchet strap and stair climbers is much safer.

Moving blankets and tape or stretch wrap to protect the finish and keep doors closed.

Transit bolts for a front-load washer, if you still have them. If not, they can usually be ordered by model number from the manufacturer.

Pliers or an adjustable wrench, a bucket, and towels for disconnecting hoses.

A helper. Two people minimum for any washer or dryer, and three for stairs.

Step 1: Clean and Dry the Washer

Run an empty cycle with hot water a day or two before moving, then leave the door or lid open so the drum dries completely. A washer that travels with moisture inside can grow mold and develop a smell that is hard to get rid of. Clean the dryer lint trap and, if you can, the vent duct as well.

Step 2: Disconnect the Washer

Turn off the hot and cold water valves behind the washer. Unplug the power cord. Place a bucket under the hose connections, then unscrew the supply hoses from the wall valves and from the back of the washer. Drain the hoses into the bucket.

Next, pull out the drain hose from the standpipe or sink and let it empty. Many front-load washers also have a small drain filter near the bottom front. Draining it removes the last of the water and is the step people most often skip.

Pack the hoses in a labeled bag. Rubber supply hoses older than five years or so are worth replacing with braided stainless steel hoses at the new house. It is a cheap way to avoid a burst-hose flood.

Step 3: Install Transit Bolts on a Front-Load Washer

This is the most important step for front-load washers. The drum is suspended on springs and dampers, and without support it will bounce around during transport and can damage the suspension.

Transit bolts, also called shipping bolts, lock the drum in place. They were removed when the washer was first installed, and they screw back into holes on the back panel. If you no longer have them, look up your model number and order them, or ask the manufacturer for the correct part. Avoid improvised fixes like stuffing towels into the drum, which do not support it the way bolts do.

Top-load washers do not use transit bolts, but some manufacturers recommend a stabilizing kit or packing material between the tub and the cabinet. Check the manual for your model. Either way, tape the lid shut.

Step 4: Disconnect the Dryer

Electric dryers simply unplug. Note whether your dryer has a 3-prong or 4-prong cord. Newer homes typically have 4-prong outlets, while many older homes have 3-prong outlets, and the cord may need to be swapped to match the outlet at the new house. That is a simple job with the right cord kit, but if you are not comfortable working with 240-volt wiring, have an electrician do it.

Gas dryers require more care. The gas supply valve must be turned off and the flexible gas line disconnected and capped. Plan on a licensed plumber or appliance technician for both the disconnect and the reconnect, and call your gas utility, such as Citizens Energy Group inside Indianapolis, if you have any questions or smell gas. This is not a job to improvise.

Then disconnect the vent duct from the back of the dryer. If you have foil or plastic duct, replace it with semi-rigid metal duct at the new house. It is safer and dries clothes faster.

Step 5: Protect and Move the Appliances

Tape doors, lids, and cords closed, then wrap each appliance in moving blankets. Tilt the appliance back onto the dolly, strap it in place, and wheel it out. Have one person guide from the front and one control the dolly.

On stairs, an appliance dolly with stair climbers is a big help. Take it one step at a time with one person below and one above, and never stand directly downhill of an appliance on stairs.

Stacked washer and dryer units must be separated first. Most use a stacking kit that unbolts or unclips. The dryer is lifted off the washer by two people, then each unit is moved separately.

Step 6: Load and Secure in the Truck

Keep washers and dryers upright. Laying a washer on its side or back can damage the suspension and leave residual water in places it should not be. Load them against the truck wall, strap them in tight, and keep the doors facing the wall so they cannot open. U-Haul’s washer and dryer guide follows the same approach.

Step 7: Set Up at the New Home

Before installing, measure the new laundry space and confirm the water connections, drain, outlet type, and vent location. Laundry closets in new construction around Indianapolis can be tight, and outlet types vary from house to house.

Remove the transit bolts from a front-load washer before running it, and save them in a labeled bag taped to the back of the machine for your next move. Running a front-loader with the bolts in can seriously damage it.

Level each appliance by adjusting the feet, connect the hoses and power, and run a short test cycle while you watch for leaks. Then reconnect the dryer vent and check that it pushes air outside.

Can One Person Move a Washer and Dryer?

With an appliance dolly on a flat floor, one person can move a dryer or a top-load washer a short distance. Getting either one onto the dolly, up a ramp, or onto a truck safely takes two people. Front-load washers and anything on stairs always need at least two. Moving them alone is one of the most common ways people get hurt during a DIY move.

How Expensive Is It to Move a Washer and Dryer?

If you are moving the rest of your home, a washer and dryer usually add only a little time to the job. Most movers charge by the hour, so the cost depends on access, such as basement stairs or tight closets, rather than the appliance itself. Gas disconnects and reconnects by a plumber are a separate cost. See our pricing page for how hourly rates work, or schedule an in-home moving estimate if you have tricky access.

Moving appliances to a different spot in the same house, such as relocating laundry from a basement to an upstairs room, is a different project. That usually needs a plumber and an electrician for new water, drain, power, and vent connections.

Should You Move Your Old Washer and Dryer at All?

It is worth asking. If your appliances are more than ten years old, or the new house already has a set, it may make more sense to sell or haul away the old ones. Our junk removal service can take them on moving day. If you are between homes, washers and dryers store well in climate-controlled storage once they are fully dried, with doors propped slightly open to prevent odors.

Let Movers Handle the Heavy Lifting

Washers and dryers are part of every residential move we do, and our crews have the appliance dollies, straps, and blankets to move them safely. For other heavy items, see our guides on moving specialty items, how to move a piano, and how to move a mattress. The Home Depot’s washing machine guide is another good resource for the disconnect steps.

Whether you are moving across town with our local moving team or across the country with our long-distance movers, request a free quote and we will take care of the heavy lifting.

Frequently Asked Questions About Moving a Washer and Dryer

Can you lay a washing machine down to move it? No. Keep washers upright. Laying one on its side or back can damage the suspension and leave water where it should not be.

What are transit bolts on a washing machine? Transit bolts lock the drum of a front-load washer in place during transport. Install them before moving and remove them before using the washer again.

What if I lost my washer’s transit bolts? Order replacements from the manufacturer using your model number. Avoid improvised fixes, which do not support the drum properly.

Do movers disconnect gas dryers? Gas lines should be disconnected and reconnected by a licensed plumber or appliance technician. Check with your moving company about what their crews can and cannot handle.

How long should a washer sit after moving? If it stayed upright, you can install it right away. If it was tilted or laid down, let it sit upright for a few hours so any water inside drains back into place, then run a short test cycle and check for leaks.